960RPM 风量:24739M3/H 2.2KW 防爆风机BT35-11-8/380V依客思

 960RPM 风量:24739M3/H 2.2KW 防爆风机BT35-11-8/380V 依客思
2.2KW explosion-proof fan BT35-11-8/380V Ekes  960RPM 风量:24739M3/H 2.2KW 防爆风机BT35-11-8/380V 依客思
T35-11(T40-11)系列轴流式通风机是我国八十年代在T30-11的基础上改进设计的新型风机它与T30-11风机相比具有明显优点：
◆ 结构更合理
◆ 性能有较大提高，全压效力为89.5%。
◆ 噪声更低，噪声（比A声级）降低3.6dB（A）。
本系列风机适用于输送易燃易爆无腐蚀性气体，环境温度不得超过60℃。 广泛应用于一般工厂、仓库、办公室、住宅内通风换气或强暖气散热，也可在较长的排气管道内间隔串联安装以提高管道中的压力 ，卸下电机可做自由风扇。防腐轴流式风机(FT35-11型)采用防腐材料外涂环氧漆加工而成，电机采用特种防腐电机用于输送有腐蚀性气体。防爆轴流式风机 ( BT35-11 ) 型，用于输送易燃易爆的气体。叶轮由铝合金加工而成， 以防止在运转中引起火花, 电机采用隔爆型电机。FT35-11型和BT35-11型风机的性能参数和外形尺寸均同T35-11型风机一样。风机需带支架脚和电机电压，请订货时注明。

 960RPM 风量:24739M3/H 2.2KW 防爆风机BT35-11-8/380V 依客思安装说明

◆ 安装前应详细检查风机是否有损坏变形，如有损坏变形，待修理妥善后，方可进行安装。

◆ 安装时要注意检查各不如部分有无松动，叶片与风筒间隙应均匀，不得相碰。

◆ 连接风口管道的重量不应由风机的风筒承受，安装时应另加支撑。

◆ 在风机风口端必须装集风器，并安装防护网。

◆ 风机底座必须与地基平面自然接合，不得敲打底座强制联接，以防底座变形，安装时应校正机座，加垫铁片、保持水平位置，然后拧紧地脚螺栓。

◆ 安装完毕后，必须先进行实验，待运行正常后，才允许正式使用。

An overview of the fan

T35-11(T40-11) series axial flow fan is a new type fan improved on the basis of T30-11 in China in the 1980s. Compared with T30-11 fan, it has obvious advantages:

◆ More reasonable structure

◆ The performance is greatly improved, the full pressure efficiency is 89.5%.

◆ Lower noise, noise (than A sound level) reduced 3.6dB (A).

This series of fans are suitable for conveying inflammable, explosive and non-corrosive gases, and the ambient temperature shall not exceed 60℃. Widely used in general factories, warehouses, offices, residential ventilation or strong heating heat dissipation, but also in long exhaust pipe interval series installation to improve the pressure in the pipe, unloaded motor can be a free fan. Anticorrosive axial flow fan (FT35-11) is made of anticorrosive material coated with epoxy paint, and the motor adopts special anticorrosive motor for conveying corrosive gases. Explosion-proof axial flow fan (BT35-11) is used for conveying inflammable and explosive gases. The impeller is made of aluminum alloy to prevent spark in operation. The motor adopts flameproof motor. The performance parameters and dimensions of FT35-11 and BT35-11 fans are the same as t35-11 fans. Fan must have bracket and motor voltage, please indicate when ordering.



→ Fan installation instructions



Before installation, check whether the fan is damaged or deformed. If there is damage or deformation, it can be installed only after proper repair.



The installation should pay attention to check whether the parts are loose, blade and air duct clearance should be uniform, not to touch.



The weight of the pipe connecting the tuyere should not be borne by the air duct of the fan, and should be supported during installation.



The air collector must be installed at the tuyere end of the fan and the protective net must be installed.



◆ The fan base must naturally engage with the foundation plane. It is not allowed to force the connection by beating the base to prevent the base from deformation. During installation, the base should be corrected, and iron plates should be added to keep the horizontal position, and then the anchor bolts should be tightened.



After the installation, you must carry out the experiment first, until the normal operation, to allow formal use.