依客思防爆声光报警器bbj-2大功率220v工业120分贝消防警示器危险报BBJ
详细信息
| | 品牌：依客思 | | 类型：防爆应急灯 | | 加工定制：是 | |
| | 光源类型：LED | | 光源功率：3-10 W | | 电压：2436220 V | |
| | 防护等级：IP65 | | 主要适用范围：当生产现场发生事故或火灾等紧急情况时，能由火灾报警控制器启 | | 型号：BBJ | |
防爆声光报警器是一种结合了声音和光线报警功能的安全装置，专为含有爆炸性气体环境场所设计。以下是对防爆声光报警器的详细介绍：
一、概述
防爆声光报警器（简称报警器）为非编码型报警器，适用于安装在含有ⅡC（ⅡB）级T6温度组别的爆炸性气体环境场所。当生产现场发生事故或火灾等紧急情况时，火灾报警控制器送来的控制信号启动声光报警电路，发出声和光报警信号，以完成报警目的。本产品也可同手动报警按钮配合使用，达到简单的声、光报警目的。
二、技术参数
防爆标志：ExdⅡbT6
工作电压：DC24V；AC220V（也有AC127V的选项）
报警电流：DC24V时≤600mA
频闪频率：60次/min
声响强度：100-115dB
声响形式：消防声（可根据用户需求设计成警笛声、救护车声）
防护等级：IP65或无防护
使用环境：温度：-20℃-+50℃；相对湿度：≤95% 不结露；大气压力：80KPa-110KPa
进线口径：M22×1.5（进线口径的数量及大小可以根据用户的需求设计生产）
重量：1.4Kg
三、产品特点
报警器外壳为全不锈钢壳体或ZL102铝合金压铸成型，表面高压静电喷塑，具有高强度和耐腐蚀性。
灯壳抗冲击能力强，采用360°清晰可视超高亮LED发光管，配备超强蜂鸣器，确保在恶劣环境下稳定工作。
报警器具有工作稳定、使用寿命长、功耗低的特点，且不受污染物和水的影响。
四、安装与布线
根据现场情况，使用M6膨胀螺钉或M6螺钉将火灾声光报警器的防爆外壳固定在墙壁上。
连接电缆外径为φ6～8mm的橡塑电缆，电缆的防爆进线口为M22×1.5螺纹，可与镀锌护管或BNG15×700防爆挠管连接，也可以使用防爆封口螺帽锁紧。
接线时，需按照防爆火灾声光报警器布线示意图，将控制线分极性分别接在火灾声光报警器接线端子的+、—两端。注意防爆面不要夹杂导线或其它异物。
布线要求：线间、线与大地间绝缘阻抗大于20MΩ，探测总线回路单根线路电阻小于20Ω。
五、适用范围
防爆声光报警器适用于石油、化工、矿山、隧道等易燃易爆场所，以及家庭、学校、商场等公共场所。一旦探测器检测到异常情况，如火灾、气体泄漏等，能够迅速响应，发出高分贝的警报声和强烈的光闪，以引起人们的注意，并采取紧急措施。
总之，防爆声光报警器以其独特的防爆性能和高效、直观的报警方式，成为守护每一刻的重要工具。
Explosion-proof sound and light alarm is a combination of sound and light alarm function of the safety device, specially designed for places containing explosive gas environment. The following is a detailed introduction to the explosion-proof sound and light alarm:
I. Overview
Explosion-proof sound and light alarm (referred to as alarm) is a non-coding alarm, suitable for installation in explosive gas environments containing ⅡC (ⅡB) class T6 temperature group. When an accident or fire and other emergency occurs on the production site, the control signal sent by the fire alarm controller starts the sound and light alarm circuit and sends out the sound and light alarm signal to complete the alarm purpose. This product can also be used with manual alarm buttons to achieve simple acoustic and optical alarm purposes.
2. Technical parameters
Explosion-proof mark: ExdⅡbT6
Working voltage: DC24V; AC220V (also available with AC127V option)
Alarm current: DC24V ≤600mA
Stroboscopic frequency: 60 times /min
Sound intensity: 100-115dB
Sound form: fire sound (can be designed as a police siren, ambulance sound according to user needs)
Protection level: IP65 or no protection
Operating environment: Temperature: -20℃-+50℃; Relative humidity: ≤95% no condensation; Atmospheric pressure: 80KPa-110KPa
Inlet diameter: M22×1.5 (The quantity and size of inlet diameter can be designed and produced according to the needs of users)
Weight: 1.4Kg
Third, product characteristics
The shell of the alarm is made of stainless steel shell or ZL102 aluminum alloy die-casting molding, the surface of high voltage electrostatic spray, with high strength and corrosion resistance.
The lamp shell has strong impact resistance, adopts 360° clear visual ultra-bright LED light tube, and is equipped with super buzzer to ensure stable operation in harsh environment.
The alarm has the characteristics of stable operation, long service life, low power consumption, and is not affected by pollutants and water.
Fourth, installation and wiring
Use M6 expansion screws or M6 screws to secure the explosion-proof shell of the fire sound and light alarm to the wall according to the site conditions.
Connect the rubber and plastic cable with an outer diameter of φ6 ~ 8mm, and the explosion-proof inlet of the cable is M22×1.5 thread, which can be connected with the galvanized protective pipe or BNG15×700 explosion-proof flexible pipe, and can also be locked by explosion-proof sealing nuts.
When connecting cables, connect the control cables to the + and - ends of the wiring terminals of the fire alarm according to the wiring diagram of the explosion-proof fire alarm. Pay attention to the explosion-proof surface do not include wire or other foreign matter.
Wiring requirements: The insulation impedance between wires and between wires and the ground is greater than 20MΩ, and the resistance of a single line of the probe bus loop is less than 20Ω.
V. Scope of application
Explosion-proof sound and light alarm is suitable for flammable and explosive places such as petroleum, chemical industry, mines, tunnels, as well as public places such as families, schools, shopping malls. Once the detector detects an abnormal situation, such as fire, gas leakage, etc., it can respond quickly, emit a high-decibel alarm and a strong light flash to attract people's attention and take emergency measures.
In short, explosion-proof sound and light alarm with its unique explosion-proof performance and efficient and intuitive alarm mode, become an important tool to guard every moment.
扫一扫，手机浏览
防爆声光报警器是一种结合了声音和光线报警功能的安全装置，专为含有爆炸性气体环境场所设计。以下是对防爆声光报警器的详细介绍：
依客思防爆科技有限公司15392918022
￥119.00
